防静电自流平基面处置案例

宣布日期:2018-06-24 阅读次数:101

环氧防静电自流平地坪被称之为车间防静电地坪,其成膜丰硕,固含量高,具有超强的耐压、耐磨机能,并且硬度好,耐刮伤,面层具有很好的耐磨性,耐久耐用。合用于通信装备制作厂、紧密电子制作厂、计较机房、病院手术室、及有防静电请求的场所。因为一些高科技型电子企业,它对地坪机能有着极高的请求,除耐压耐磨耐打击以外还要具有防静电功效。那末环氧防静电地坪对基面有如何的请求呢?首要有以下四点请求:

Epoxy anti-static self-leveling floor is called workshop anti-static floor. It has rich film, high solid content, super pressure and wear resistance, good hardness, scratch resistance, good wear resistance and durability. It is suitable for communication equipment manufacturers, precision electronics manufacturers, computer rooms, hospital operating rooms, and places with anti-static requirements. Because some high-tech electronic enterprises, it has very high requirements for floor performance, in addition to pressure, wear and impact resistance, but also has anti-static function. So what are the requirements of epoxy anti-static floor for the base surface? There are four main requirements: 第一点:下层打磨与清算

First point: grass-roots grinding and cleaning

施工前,必然要辨别开施工地区,起首将空中各类渣滓清算清洁,包含表层积水、油污、旧漆膜等等,而后停止打磨,确保空中平坦。若是空中有高低不平的处所,能够用手磨机或是砂纸停止部分打磨。

Before the construction, we must distinguish the construction area, first clean up all kinds of rubbish on the ground, including surface water, oil, old paint film, etc., and then grind to ensure the smooth surface. If the ground is rough, you can use a hand grinder or sandpaper for local grinding.

为了加强与树脂之间的连系力,需将水泥基面打毛,最初操纵吸尘器清算,清算后的空中要坚持封锁状况。

In order to enhance the bonding force with the resin, the cement base surface needs to be groomed, and finally cleaned with a vacuum cleaner. After cleaning, the ground should be kept closed.第二点:地坪的固砂与修补

Second point: sand consolidation and repair of floor

若是空中存在藐小裂痕,倡议你先操纵环氧树脂停止修补,而后再停止自流平的施工。

If there are small cracks in the ground, it is recommended that you use epoxy resin to repair them first, and then carry out self-leveling construction.第三点:地坪基面请求

Third point: Floor base requirements

对防静电环氧自流平地坪来讲,它请求空中强度在C20以上,操纵2m靠尺查抄时请求误差小于2mm,并且外表不能有任何油污等污物。

For the anti-static epoxy self-leveling floor, it requires that the ground strength should be above C20, the deviation should be less than 2mm when checking with 2m ruler, and there should be no oil contamination on the surface.第四点:外表含水率请求

Fourth point: surface moisture requirement

因为防静电环氧自流平对外表的含水率有严酷请求,以是施工前要停止含水率测定,含水率不能跨越8%,若是空中含水率超标的话,就要接纳喷灯烘干,喷灯也便是喷火灯。

Because anti-static epoxy self-leveling has strict requirements for surface moisture content, water content should be measured before construction. Water content can not exceed 8%. If the surface moisture content exceeds the standard, it is necessary to use a spray lamp to dry, that is, a spray lamp.

辛劳清算!转载请说明来自 http://elsmithint.com/show.asp?id=127

你感觉这篇防静电自流平基面处置案例文章怎样样?

0 0
在线征询
微信征询
接洽德律风
137-7148-9633
前往顶部